Guide · Suno noise
How to remove noise from Suno songs
Most Suno songs carry three kinds of noise: a steady hiss, a cloudy “fog” in the low mids, and a metallic shimmer in the highs. Each needs different treatment, and all three must be dealt with before the song is made louder.
Short answer
Download the WAV from Suno, lower it by about 3 dB, reduce the noise floor gently with spectral noise reduction, control the shimmer above about 6 kHz with a de-esser or dynamic EQ, then compress and master. Do it in that order: a limiter makes every kind of noise louder.
Decodec does all of this automatically. Upload a song, hear a 30-second preview of your own track, adjust the settings, and download a 24-bit WAV master. A single track costs $2.99.
The three kinds of noise
- Hiss: a constant noise floor under the whole track. You hear it in quiet intros, breakdowns and fade-outs. See the guide to removing Suno hiss.
- Fog: a dull, cloudy layer roughly between 250 Hz and 2 kHz that makes the mix sound muddy and boxed in.
- Shimmer: unstable, metallic movement between about 6 and 12 kHz, most obvious on cymbals, S sounds and reverb tails. See the guide to fixing AI shimmer.
None of these can be prompted away. They come from the way AI generators produce audio, so most generations carry some of each.
Clean it yourself for free
- Download the WAV. MP3 compression adds artifacts in the same frequency range as the shimmer.
- Turn the file down by about 3 dB so later processing has room to work without clipping.
- Use spectral noise reduction (Audacity’s Noise Reduction is free) with a small amount, around 3 to 6 dB. More than that makes vocals sound watery.
- For fog, use a gentle, wide EQ dip in the low mids, only if the mix sounds muddy.
- For shimmer, add a de-esser or dynamic EQ band across 6 to 12 kHz that acts only when the top end jumps out.
- Compress lightly, add back a little brightness around 4 kHz if the noise reduction dulled the song, then limit to about −11 LUFS with peaks under −1 dBFS.
The most common mistake is too much noise reduction. A slightly noisy song sounds better than a muffled one.
Remove it automatically with Decodec
Decodec runs the same order as a mastering engineer’s chain: noise reduction, de-essing, compression, tonal control, EQ, clipping and a true-peak limiter, with triangular dither on the final file.
Before you pay you can change noise reduction (Less, Normal, More), turn fog and shimmer reduction on or off, and set de-essing, compression, tonal balance and brightness, then re-render your preview. You pay only for the version you choose.
Pricing: $2.99 per track, $19 for 10 tracks, or $29 for an engineer to restore it by hand within 48 hours. One-time payments, no subscription.
Questions
What is the best way to remove noise from a Suno song?
Reduce the noise before mastering, not after. Use gentle spectral noise reduction for the hiss, a dynamic EQ or de-esser for the metallic highs, then master. Decodec does this automatically and lets you hear and adjust a preview before paying.
Can I remove Suno noise for free?
Yes. Audacity’s Noise Reduction and a free de-esser plugin can do a reasonable job if you keep the settings gentle. It takes more time and the results vary from song to song.
Why does my Suno song sound muddy or metallic?
AI generators create audio by predicting and decoding it, which leaves a noise floor, a cloudy low-mid layer and unstable highs. They are part of the file, so a new prompt rarely fixes them.
Does removing the noise change the song?
No. Melody, lyrics, arrangement and vocals stay as generated. Only the noise and artifacts are reduced, and the track is mastered.
Does this work for Udio and Mozart AI songs?
Yes. Those generators leave the same kinds of noise, and Decodec processes their exports the same way.